#Esky belt cp v2 manual
#Esky belt cp v2 upgrade
#Esky belt cp v2 full

It's work to fly but went much better than I expected. With totally fresh apperance and new designs for the main.

#Esky belt cp v2 upgrade

I put on Blade 400 325mm wood blades (because I had them and they fit the esky blade grips).Īnd I'm flying this in 10-15mph of wind! :-) The latest ESky Belt-CP V2 is an upgrade version of the world famous ESky Belt-CP RC helicopter. Link pieces work for the two swash to blade links. I used only hardware that was stock that came with the Belt CP V2 for linkage. Well, I'm flying on stock sloppy linkage stock servos (all 4) Top of the head replacement parts left but I had enough spares to rebuild it So I followed up myself, I had to know! + after my last crash I did not have any did they have to modify this?Īnyhow I have many complaints on how these people started but never followed Or story on how converting to flybarless and not using any kind of stabilization system worked out for them.ĭid it suck? did they give up? do they still ever try it? which helicopter does it work best on? On a Belt CP V2, they have this sloppy indirect linkage as opposed to direct short links to the 3 cyclic servos. Never do more than hover and then they NEVER follow-up on the projectĪnd report how it went nor do they ever come back and provide more videos I've seen a lot of youtube videos where people *start* on this project but (with motor unplugged of course!) All dependent on your particular head setup.Belt CP V2 Flybarless with no stabilization system except the stock tail gyro.

#Esky belt cp v2 full

at full deflections (min/max throt and min/max aile and elev at the same time). In AliExpress, you can also find other good deals on remote control toys, toys & hobbies and parts & accs You can shop for esky belt cp v2 parts at low prices. This model file I am attaching is all zero sub-trims, so please go through the typical on-heli CCPM setup and center your servo arms and check your travel for things moving too far, interfering, bumping, etc. Looking for esky belt cp v2 parts Esky belt cp parts are precision machined from high quality materials, with high strength and good performance. RoJAck wrote: Ok, my quick test flight to prove it works was successful, but will need some sub-trims. Please do check all your servo motions before attempting to fly. I'm definitely not saying that you should just load this and fly, but it is a starting point, and it got my heli off the ground. 1&2 are both 100% throw (D/R) with the same 30% expo. Flight mode 2 is a slightly higher throttle setting. Expo is 30% on Ail, Ele, and Rud.įlight mode 1 is the standard V throttle curve with 50% at mid-stick and -/+ 100% at the ends. Throttle hold is set to always set throttle to -100 and use the full pitch curve.įlight mode 0 sets AIL and ELEV servo throw (D/R) to 70% and limits negative pitch to something like -10% at full down throttle. My setup basically only uses the flight mode switch and the throttle hold. I'm not sure if the gyro gain is really adjustable or not, but you could set this up to a fixed value of say '50' for starters if you wanted, or hook it to the flight mode switch for a few different values.

#Esky belt cp v2 manual

I put the GYRO channel on my AUX5 rotary knob to make it easy to adjust for me, but basically any value less than 0 is 'rate mode', and above 0 is 'heading hold' mode. esky BELT-CP V2 CX 2,4 GHz Manual Online: vue eclate belt cp v2 cx, Verbrandingstekening Belt Cp V2 Cx. Using reversing in the mixer, the AILE (ch.2) is set as reversed, and also the RUDD (ch.4) is also set as reversed. Esky Belt CP V2 / King 3 EK1-0427 Push Rod Set 000696: Condition: New.

As usual, THROT is ch.1, RUDD is ch.4, GYRO is plugged into GEAR (ch.5) as is standard. Details about Esky Belt CP V2 / King 3 EK1-0427 Push Rod Set 000696 See original listing. This made the easiest setup in the Devo10.

Registrieren Sie sich bitte, um Videos hochzuladen anmelden oder Registrieren.

Note that on the heli and Rx, I have the front servo plugged into as ELEV (ch.3), looking from above the heli down, with the nose forward, the left servo is plugged into AUX1 (ch.6), and the right servo (the side with the tail rotor) is plugged into AILE (ch.2). CNC-Metall-Upgrade für ESKY Gürtel-CP V2. I have 7 channels set, and using 'Advanced' Mixer GUI. I'm using the '120' Swash type with the defaults (normal/60). (with motor unplugged of course!) All dependent on your particular head setup. This model file I am attaching is all zero sub-trims, so please go through the typical on-heli CCPM setup and center your servo arms and check your travel for things moving too far, interfering, bumping, etc. The powerful and accuracy of the Belt-CP V2 is a true 3D. Ok, my quick test flight to prove it works was successful, but will need some sub-trims. New design from head to landing gear, the main rotor and tail rotor system has increases the stability.